View LM2904_868734.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2004 july, 2004 ? rev. 18 1 publication order number: lm358/d lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 single supply dual operational amplifiers utilizing the circuit designs perfected for quad operational amplifiers, these dual operational amplifiers feature low power drain, a common mode input voltage range extending to ground/v ee , and single supply or split supply operation. the lm358 series is equivalent to one?half of an lm324. these amplifiers have several distinct advantages over standard operational amplifier types in single supply applications. they can operate at supply voltages as low as 3.0 v or as high as 32 v, with quiescent currents about one?fifth of those associated with the mc1741 (on a per amplifier basis). the common mode input range includes the negative supply, thereby eliminating the necessity for external biasing components in many applications. the output voltage range also includes the negative power supply voltage. features ? short circuit protected outputs ? true differential input stage ? single supply operation: 3.0 v to 32 v ? low input bias currents ? internally compensated ? common mode range extends to negative supply ? single and split supply operation ? esd clamps on the inputs increase ruggedness of the device without affecting operation ? pb?free packages are available ? ncv prefix for automotive and other applications requiring site and control changes pdip?8 n, an, vn suffix case 626 1 8 soic?8 d, vd suffix case 751 1 8 pin connections v ee /gnd inputs a inputs b output b output a v cc ? ? + + 1 2 3 4 8 7 6 5 (top view) see general marking information in the device marking section on page 11 of this data sheet. device marking information see detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. ordering information micro8 dmr2 suffix case 846a 1 8 http://onsemi.com
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 2 single supply split supplies v cc v ee /gnd 3.0 v to v cc(max) 1 2 v cc 1 2 v ee 1.5 v to v cc(max) 1.5 v to v ee(max) output bias circuitry common to both amplifiers v cc v ee /gnd inputs q2 q3 q4 q5 q26 q7 q8 q6 q9 q11 q10 q1 2.4 k q25 q22 40 k q13 q14 q15 q16 q19 5.0 pf q18 q17 q20 q21 2.0 k q24 q23 q12 25 figure 1. figure 2. representative schematic diagram (one?half of circuit shown)
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 3 maximum ratings (t a = +25 c, unless otherwise noted.) rating symbol value unit power supply voltages single supply split supplies v cc v cc , v ee 32 16 vdc input differential voltage range (note 1) v idr 32 vdc input common mode voltage range (note 2) v icr ?0.3 to 32 vdc output short circuit duration t sc continuous junction temperature t j 150 c thermal resistance, junction?to?air (note 3) r ja 238 c/w storage temperature range t stg ?55 to +125 c esd protection at any pin human body model machine model v esd 2000 200 v operating ambient temperature range lm258 lm358 LM2904/LM2904a LM2904v, ncv2904 (note 4) t a ?25 to +85 0 to +70 ?40 to +105 ?40 to +125 c maximum ratings are those values beyond which device damage can occur. maximum ratings applied to the device are individual str ess limit values (not normal operating conditions) and are not valid simultaneously. if these limits are exceeded, device functional operation i s not implied, damage may occur and reliability may be affected. 1. split power supplies. 2. for supply voltages less than 32 v the absolute maximum input voltage is equal to the supply voltage. 3. r ja for case 846a. 4. ncv2904 is qualified for automotive use.
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 4 electrical characteristics (v cc = 5.0 v, v ee = gnd, t a = 25 c, unless otherwise noted.) lm258 lm358 characteristic symbol min typ max min typ max unit input offset voltage v cc = 5.0 v to 30 v, v ic = 0 v to v cc ?1.7 v, v o 1.4 v, r s = 0 v io mv t a = 25 c ? 2.0 5.0 ? 2.0 7.0 t a = t high (note 5) ? ? 7.0 ? ? 9.0 t a = t low (note 5) ? ? 7.0 ? ? 9.0 average temperature coefficient of input offset voltage v io / t ? 7.0 ? ? 7.0 ? v/ c t a = t high to t low (note 5) input offset current i io ? 3.0 30 ? 5.0 50 na t a = t high to t low (note 5) ? ? 100 ? ? 150 input bias current i ib ? ?45 ?150 ? ?45 ?250 t a = t high to t low (note 5) ? ?50 ?300 ? ?50 ?500 average temperature coefficient of input offset current i io / t ? 10 ? ? 10 ? pa/ c t a = t high to t low (note 5) input common mode voltage range (note 6), v cc = 30 v v icr 0 ? 28.3 0 ? 28.3 v v cc = 30 v, t a = t high to t low 0 ? 28 0 ? 28 differential input voltage range v idr ? ? v cc ? ? v cc v large signal open loop voltage gain a vol v/mv r l = 2.0 k , v cc = 15 v, for large v o swing, 50 100 ? 25 100 ? t a = t high to t low (note 5) 25 ? ? 15 ? ? channel separation cs ? ?120 ? ? ?120 ? db 1.0 khz f 20 khz, input referenced common mode rejection cmr 70 85 ? 65 70 ? db r s 10 k power supply rejection psr 65 100 ? 65 100 ? db output voltage?high limit t a = t high to t low (note 5) v oh v v cc = 5.0 v, r l = 2.0 k , t a = 25 c 3.3 3.5 ? 3.3 3.5 ? v cc = 30 v, r l = 2.0 k 26 ? ? 26 ? ? v cc = 30 v, r l = 10 k 27 28 ? 27 28 ? output voltage?low limit v ol ? 5.0 20 ? 5.0 20 mv v cc = 5.0 v, r l = 10 k , t a = t high to t low (note 5) output source current i o + 20 40 ? 20 40 ? ma v id = +1.0 v, v cc = 15 v output sink current i o ? v id = ?1.0 v, v cc = 15 v 10 20 ? 10 20 ? ma v id = ?1.0 v, v o = 200 mv 12 50 ? 12 50 ? a output short circuit to ground (note 7) i sc ? 40 60 ? 40 60 ma power supply current (total device) t a = t high to t low (note 5) i cc ma v cc = 30 v, v o = 0 v, r l = ? 1.5 3.0 ? 1.5 3.0 v cc = 5 v, v o = 0 v, r l = ? 0.7 1.2 ? 0.7 1.2 5. lm258: t low = ?25 c, t high = +85 c lm358: t low = 0 c, t high = +70 c LM2904/LM2904a: t low = ?40 c, t high = +105 c LM2904v & ncv2904: t low = ?40 c, t high = +125 c ncv2904 is qualified for automotive use. 6. the input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 v. the upp er end of the common mode voltage range is v cc ? 1.7 v. 7. short circuits from the output to v cc can cause excessive heating and eventual destruction. destructive dissipation can result from simultaneous shorts on all amplifiers.
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 5 electrical characteristics (v cc = 5.0 v, v ee = gnd, t a = 25 c, unless otherwise noted.) LM2904 LM2904a LM2904v, ncv2904 characteristic symbol min typ max min typ max min typ max unit input offset voltage v cc = 5.0 v to 30 v, v ic = 0 v to v cc ?1.7 v, v o 1.4 v, r s = 0 v io mv t a = 25 c ? 2.0 7.0 ? 2.0 7.0 ? ? 7.0 t a = t high (note 8) ? ? 10 ? ? 10 ? ? 13 t a = t low (note 8) ? ? 10 ? ? 10 ? ? 10 average temperature coefficient of input offset voltage v io / t ? 7.0 ? ? 7.0 ? ? 7.0 ? v/ c t a = t high to t low (note 8) input offset current i io ? 5.0 50 ? 5.0 50 ? 5.0 50 na t a = t high to t low (note 8) ? 45 200 ? 45 200 ? 45 200 input bias current i ib ? ?45 ?250 ? ?45 ?100 ? ?45 ?250 t a = t high to t low (note 8) ? ?50 ?500 ? ?50 ?250 ? ?50 ?500 average temperature coefficient of input offset current i io / t ? 10 ? ? 10 ? ? 10 ? pa/ c t a = t high to t low (note 8) input common mode voltage range (note 9), v cc = 30 v v icr 0 ? 24.3 0 ? 24.3 0 ? 24.3 v v cc = 30 v, t a = t high to t low 0 ? 24 0 ? 24 0 ? 24 differential input voltage range v idr ? ? v cc ? ? v cc ? ? v cc v large signal open loop voltage gain a vol v/mv r l = 2.0 k , v cc = 15 v, for large v o swing, 25 100 ? 25 100 ? 25 100 ? t a = t high to t low (note 8) 15 ? ? 15 ? ? 15 ? ? channel separation cs ? ?120 ? ? ?120 ? ? ?120 ? db 1.0 khz f 20 khz, input referenced common mode rejection cmr 50 70 ? 50 70 ? 50 70 ? db r s 10 k power supply rejection psr 50 100 ? 50 100 ? 50 100 ? db output voltage?high limit t a = t high to t low (note 8) v oh v v cc = 5.0 v, r l = 2.0 k , t a = 25 c 3.3 3.5 ? 3.3 3.5 ? 3.3 3.5 ? v cc = 30 v, r l = 2.0 k 22 ? ? 22 ? ? 22 ? ? v cc = 30 v, r l = 10 k 23 24 ? 23 24 ? 23 24 ? output voltage?low limit v ol ? 5.0 20 ? 5.0 20 ? 5.0 20 mv v cc = 5.0 v, r l = 10 k , t a = t high to t low (note 8) output source current i o + 20 40 ? 20 40 ? 20 40 ? ma v id = +1.0 v, v cc = 15 v output sink current i o ? v id = ?1.0 v, v cc = 15 v 10 20 ? 10 20 ? 10 20 ? ma v id = ?1.0 v, v o = 200 mv ? ? ? ? ? ? ? ? ? a output short circuit to ground (note 10) i sc ? 40 60 ? 40 60 ? 40 60 ma power supply current (total device) t a = t high to t low (note 8) i cc ma v cc = 30 v, v o = 0 v, r l = ? 1.5 3.0 ? 1.5 3.0 ? 1.5 3.0 v cc = 5 v, v o = 0 v, r l = ? 0.7 1.2 ? 0.7 1.2 ? 0.7 1.2 8. lm258: t low = ?25 c, t high = +85 c lm358: t low = 0 c, t high = +70 c LM2904/LM2904a: t low = ?40 c, t high = +105 c LM2904v & ncv2904: t low = ?40 c, t high = +125 c ncv2904 is qualified for automotive use. 9. the input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 v. the upp er end of the common mode voltage range is v cc ? 1.7 v. 10. short circuits from the output to v cc can cause excessive heating and eventual destruction. destructive dissipation can result from simultaneous shorts on all amplifiers.
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 6 circuit description the lm358 series is made using two internally compensated, two?stage operational amplifiers. the first stage of each consists of differential input devices q20 and q18 with input buffer transistors q21 and q17 and the differential to single ended converter q3 and q4. the first stage performs not only the first stage gain function but also performs the level shifting and transconductance reduction functions. by reducing the transconductance, a smaller compensation capacitor (only 5.0 pf) can be employed, thus saving chip area. the transconductance reduction is accomplished by splitting the collectors of q20 and q18. another feature of this input stage is that the input common mode range can include the negative supply or ground, in single supply operation, without saturating either the input devices or the differential to single?ended converter. the second stage consists of a standard current source load amplifier stage. each amplifier is biased from an internal?voltage regulator which has a low temperature coefficient thus giving each amplifier good temperature characteristics as well as excellent power supply rejection. figure 3. large signal voltage follower response 5.0 s/div 1.0 v/div v cc = 15 vdc r l = 2.0 k t a = 25 c a vol , open loop voltage gain (db) v , input voltage (v) i figure 4. input voltage range figure 5. large?signal open loop voltage gain 18 16 14 12 10 8.0 6.0 4.0 2.0 0 20 0 2.0 4.0 6.0 8.0 10 12 14 16 18 20 v cc /v ee, power supply voltages (v) 120 100 80 60 40 20 0 -20 1.0 10 100 1.0 k 10 k 100 k 1.0 m f, frequency (hz) negative positive v cc = 15 v v ee = gnd t a = 25 c
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 7 v or , output voltage range (v ) pp v o , output voltage (mv) figure 6. large?signal frequency response figure 7. small signal voltage follower pulse response (noninverting) figure 8. power supply current versus power supply voltage figure 9. input bias current versus supply voltage 14 12 10 8.0 6.0 4.0 2.0 0 1.0 10 100 1000 f, frequency (khz) 550 500 450 400 350 300 250 200 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 t, time (ms) 2.4 2.1 1.8 1.5 1.2 0.9 0.6 0.3 0 0 5.0 10 15 20 25 30 35 v cc , power supply voltage (v) v cc , power supply voltage (v) 90 80 70 0 2.0 4.0 6.0 8.0 10 12 14 16 18 20 i , power supply current (ma) cc i , input bias current (na) ib r l = 2.0 k v cc = 15 v v ee = gnd gain = -100 r i = 1.0 k r f = 100 k input output t a = 25 c r l = v cc = 30 v v ee = gnd t a = 25 c c l = 50 pf
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 8 r1 2 1 r1 t bp r1 + r2 r1 r1 + r2 1 e o e 1 e 2 e o = c (1 + a + b) (e 2 - e 1 ) r1 a r1 b r1 r c r - + 1/2 lm358 + - - + r 1/2 lm358 + - r1 r2 v o v ref v in v oh v o v ol v inl = r1 (v ol - v ref )+ v ref v inh = (v oh - v ref ) + v ref h = r1 + r2 (v oh - v ol ) r1 - + - + - + r c r2 r3 c1 100 k r c r c1 r2 100 k v in v ref v ref v ref v ref bandpass output f o = 2 rc r1 = qr r2 = r3 = t n r2 c1 = 10 c 1 notch output v ref =v cc hysteresis 1/2 lm358 1/2 lm358 1 c r v inl v inh v ref 1/2 lm358 1/2 lm358 1/2 lm358 1/2 lm358 t bp = center frequency gain t n = passband notch gain r c r1 r2 r3 for: - + f o q t bp t n = 1.0 khz = 10 = 1 = 1 = 160 k = 0.001 f = 1.6 m = 1.6 m = 1.6 m where: mc1403 1/2 lm358 - + r1 v cc v cc v o 2.5 v r2 50 k 10 k v ref v ref = v cc 2 5.0 k r c r c + 1/2 lm358 - v o 2 rc 1 for: f o = 1.0 khz r = 16 k c = 0.01 f v o = 2.5 v (1 + r1 r2 ) 1 v cc f o = figure 10. voltage reference figure 11. wien bridge oscillator figure 12. high impedance differential amplifier figure 13. comparator with hysteresis figure 14. bi?quad filter
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 9 2 1 v ref =v cc 1 2 figure 15. function generator figure 16. multiple feedback bandpass filter for less than 10% error from operational amplifier. if source impedance varies, filter may be preceded with voltage follower buffer to stabilize filter parameters. where f o and bw are expressed in hz. q o f o bw < 0.1 given: f o = center frequency a(f o ) = gain at center frequency choose value f o , c then: r3 = q f o c r3 r1 = 2 a(f o ) r1 r3 4q 2 r1 -r3 r2 = + - + - - + v ref =v cc v ref f = r1 + r c 4 cr f r1 r3 = r2 r1 r2 + r1 r2 300 k 75 k r3 r1 c triangle wave output square wave output v cc r3 r1 r2 v ref v in c c v o co co = 10 c r f if, 1/2 lm358 v ref 1/2 lm358 1/2 lm358 100 k
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 10 ordering information device operating temperature range package shipping 2 lm358d soic?8 98 units/rail lm358dr2 soic?8 2500 tape & reel lm358dr2g soic?8 (pb?free) 2500 tape & reel lm358dmr2 0 c to +70 5 c micro8 4000 tape & reel lm358dmr2g 0 cto +70 c micro8 (pb?free) 4000 tape & reel lm358n pdip?8 50 units/rail lm358ng pdip?8 (pb?free) 50 units/rail lm258d soic?8 98 units/rail lm258dr2 soic?8 2500 tape & reel lm258dr2g ?25 c to +85 c soic?8 (pb?free) 2500 tape & reel lm258dmr2 micro8 4000 tape & reel lm258n pdip?8 50 units/rail LM2904d soic?8 98 units/rail LM2904dr2 soic?8 2500 tape & reel LM2904dr2g soic?8 (pb?free) 2500 tape & reel LM2904dmr2 40 c to +105 c micro8 2500 tape & reel LM2904dmr2g ?40 c to +105 c micro8 (pb?free) 2500 tape & reel LM2904n pdip?8 50 units/rail LM2904admr2 micro8 4000 tape & reel LM2904an pdip?8 50 units/rail LM2904vd soic?8 98 units/rail LM2904vdg soic?8 (pb?free) 98 units/rail LM2904vdr2 soic?8 2500 tape & reel LM2904vdmr2 ?40 c to +125 c micro8 4000 tape & reel LM2904vn pdip?8 50 units/rail ncv2904dr2* soic?8 2500 tape & reel ncv2904dmr2* micro8 4000 tape & reel *ncv2904 is qualified for automotive use. 2for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 11 pdip?8 n suffix case 626 soic?8 d suffix case 751 marking diagrams x = 2 or 3 a = assembly location wl, l = wafer lot yy, y = year ww, w = work week pdip?8 an suffix case 626 soic?8 vd suffix case 751 pdip?8 vn suffix case 626 1 8 lmx58n awl yyww 1 8 LM2904an awl yyww 1 8 LM2904n awl yyww 1 8 LM2904vn awl yyww alyw lmx58 1 8 alyw 2904 1 8 alyw 2904v 1 8 micro8 dmr2 suffix case 846a x58 ayw 1 8 2904 ayw 1 8 904a ayw 1 8 904v ayw 1 8 *this diagram also applies to ncv2904 * *
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 12 package dimensions pdip?8 n, an, vn suffix case 626?05 issue l notes: 1. dimension l to center of lead when formed parallel. 2. package contour optional (round or square corners). 3. dimensioning and tolerancing per ansi y14.5m, 1982. 14 5 8 f note 2 ?a? ?b? ?t? seating plane h j g d k n c l m m a m 0.13 (0.005) b m t dim min max min max inches millimeters a 9.40 10.16 0.370 0.400 b 6.10 6.60 0.240 0.260 c 3.94 4.45 0.155 0.175 d 0.38 0.51 0.015 0.020 f 1.02 1.78 0.040 0.070 g 2.54 bsc 0.100 bsc h 0.76 1.27 0.030 0.050 j 0.20 0.30 0.008 0.012 k 2.92 3.43 0.115 0.135 l 7.62 bsc 0.300 bsc m --- 10 --- 10 n 0.76 1.01 0.030 0.040
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 13 package dimensions soic?8 d, vd suffix case 751?07 issue ab 1.52 0.060 7.0 0.275 0.6 0.024 1.270 0.050 4.0 0.155 mm inches scale 6:1 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* seating plane 1 4 5 8 n j x 45 k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 6. 751?01 thru 751?06 are obsolete. new standard is 751?07. a b s d h c 0.10 (0.004) dim a min max min max inches 4.80 5.00 0.189 0.197 millimeters b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.053 0.069 d 0.33 0.51 0.013 0.020 g 1.27 bsc 0.050 bsc h 0.10 0.25 0.004 0.010 j 0.19 0.25 0.007 0.010 k 0.40 1.27 0.016 0.050 m 0 8 0 8 n 0.25 0.50 0.010 0.020 s 5.80 6.20 0.228 0.244 ?x? ?y? g m y m 0.25 (0.010) ?z? y m 0.25 (0.010) z s x s m
lm358, lm258, LM2904, LM2904a, LM2904v, ncv2904 http://onsemi.com 14 package dimensions micro8 dmr2 suffix case 846a?02 issue f s b m 0.08 (0.003) a s t dim min max min max inches millimeters a 2.90 3.10 0.114 0.122 b 2.90 3.10 0.114 0.122 c --- 1.10 --- 0.043 d 0.25 0.40 0.010 0.016 g 0.65 bsc 0.026 bsc h 0.05 0.15 0.002 0.006 j 0.13 0.23 0.005 0.009 k 4.75 5.05 0.187 0.199 l 0.40 0.70 0.016 0.028 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash, protrusions or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. 846a-01 obsolete, new standard 846a-02. ?b? ?a? d k g pin 1 id 8 pl 0.038 (0.0015) ?t? seating plane c h j l 8x 8x 6x mm inches scale 8:1 1.04 0.041 0.38 0.015 5.28 0.208 4.24 0.167 3.20 0.126 0.65 0.0256 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800?282?9855 toll free usa/canada japan : on semiconductor, japan customer focus center 2?9?1 kamimeguro, meguro?ku, tokyo, japan 153?0051 phone : 81?3?5773?3850 lm358/d micro8 is a trademark of international rectifier. literature fulfillment : literature distribution center for on semiconductor p.o. box 61312, phoenix, arizona 85082?1312 usa phone : 480?829?7710 or 800?344?3860 toll free usa/canada fax : 480?829?7709 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : http://onsemi.com order literature : http://www.onsemi.com/litorder for additional information, please contact your local sales representative.

▲Up To Search▲

Price & Availability of LM2904

	To Download LM2904 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .